Colt "M" Pocket Model, Hammerless

Calibers 32 & 380 ACP,   models 1903 & 1908

 

 

The drawings listed below are scanned off existing factory catalogs, or existing books 
These Illustrated parts Drawings are shown only to help you identify needed parts, they ARE NOT parts that are made or supplied by the host of this website


Most of these illustrations will be from factory catalogs, however some are taken from Frank de Haas's Single Shot Rifle book & are for identification only, & ARE NOT factory part numbers unless identified as such.  This is important as about all obsolete parts suppliers use ONLY factory or closely associated numbers where ever possible so everyone is on the same page.

 

Note, for some of the older firearms, many over 100 years old, the factories never used what we now know as assembly drawings, but just views of many of the component parts & possibly randomly placed 

 

Actual load times may take a while as these scanned pictures may be large, & depending on the speed of your computer & server

 

The parts listed below are for your identification purposes only. 
The author of this website DOES NOT have any parts.

 

 

Above parts illustration taken from original an Colt parts list.

 1  Receiver  22  Plug
 2  Barrel (Specify Caliber)  24  Ejector
 3  Slide (Specify Caliber)  25  Ejector Pin
 4  Firing Pin, Front  26  Recoil Spring
 4a  Firing Pin, Rear  27-1  Recoil Spring Guide, complete ,Type 1
 5  Firing Pin Spring  27-2  Recoil Spring Guide, complete, Type 2
 6  Rear Sight  27-3  Recoil Spring Guide, complete, Type 3
 7  Firing Pin Lock Pin  28  Automatic Grip Safety
 8-1  Shell Extractor, early 32 cal, (single thickness)  29  Automatic Safety Pin
 8-2  Shell Extractor, late 32 & 380, (wider at hook)  30  Magazine Latch
 9  Shell Extractor Spring  31  Magazine  Complete
 10  Shell Extractor Pin  32  Magazine  Follower
 12  Hammer  33  Magazine  Spring
 13  Slide Lock Safety  34  Stocks
 14  Hammer Roll  35  Stock Screw
 15  Hammer Roll Pin  36  Safety Disconnector
 16  Trigger  37  Safety Disconnector Plunger
 17  Sear  38  Safety Disconnector Plunger Spring
 18  Safety  39  Safety Disconnector, Complete
 19  Sear & Safety Pin  40  Escutcheons, (set)
 20  Sear, Safety & Trigger Spring  41  Front Sight
 21  Main Spring . .

 

These guns were made essentially in 4 different versions, the early 32 caliber type 1, had a 4" barrel, barrel bushing, with no magazine disconnector up to s/n 71,999.  The type 2,  32 caliber used the barrel bushing but had a 3 3/4" barrel & made from 1908-1910 with s/n from 72,000 -105,051. 

Type 3, 32 caliber had no barrel bushing & 3 3/4" barrel made from 1910-1926 with s/n from 1056,051 - 468,096.  Type 4 32 calibers were the same as the type 3 but ad a magazine disconnector with s/n 468,097 - 572,214.   

The 380 caliber guns came into being in 1908 to 1940. Type 2, 380 had 3 3/4" barrels with barrel bushing were made from 1908-1910 with s/n 1-6,251.  Type 3, 380 had no barrel bushing & made from 1910-1926 with s/n from 6,252 - 92,893.   Type 4, 380 have a magazine disconnector, with s/n 92,894 - 134,499.

 

 

 

Copyright 2005- 2013  LeeRoy Wisner  with credit given for original illustrations.  All Rights Reserved

Back to Ramblings

Originated 06-25-2005 Last updated 01-12-2013
to contact the author click here